5mm Dellorto main jets in the 50's range: 50, 52, 54, 56, 58. For use in all SHA and PHBG carbs
Replacement filter for your 14.9, 14.12, 14.14,15.15 and 16.16 Dellorto SHA. Includes the screen, cap and clip.
Super nice quality supermanish shape tail light for letting the folks behind ya know you're there.
Black plastic throttle and matching 7/8 grip from Lusito.
Round black headlight with chrome rim for all mopeds. The socket in this head light uses an 1157 dual filament bulb.
Cheap effective universal puller for lots of bikes - e50, v1, m1 & m01, use it to pull an hpi etc.
1mm thick reducing shim for dellorto carburetors. Only works with 15.15 and 16.16 carbs. 21mm OD19mm ID
Authentic Dellorto SHA made in Italy. Awesome upgrade carb for most bikes. Slap this on your motobecane, peugeot, puch, minarelli, garelli, sachs, morini or tomos and forget about it. This is the click choke version.
Black domino style throttle with bonus grip already installed. This is just like the throttles that came stock on lots of Italian mopeds. Super low profile throttle assembly for a nice clean look on your bars.
5mm Dellorto main jets in the 70's range: 70, 72, 74, 76, 78. For use in all SHA and PHBG carbs.
5mm Dellorto main jets in the 80's range: 80, 82, 84, 86, 88. For use in all SHA and PHBG carbs.
Replacement petcock fuel valve for Honda Hobbit, Camino, PA50, and PA50ii. Also works on lots of Italian bikes - Garelli, Minarelli, Morini, Vespa - any bike needing a 12mm x 1mm petcock thread.
Stock tail light. This came standard on lots of bikes including puch and tomos. Fit this on pretty much any moped ever!This uses 2x single filament bulbs.
Super multi use petcock. Fits on general five star and Lazer mopeds, honda express, na50, nc50, annnnnnd yamaha qt50. Good cock to have around. 14mm x 1mm threading
Super nice quality superman shape tail light for letting the folks behind ya know you're there.
Catch all the crud with these internal banjo filters for Dellorto SHA carbs. Fits 14-16mm carbs.
Super heavy duty universal ignition condenser for wiring externally. Get some new connectors if you need them.
Red light up spark plug cap for checking your spark and having an awesome glow down by your engine.
Folding Pegs for you and a buddy. These mount over the rear shock bolt.
Clear fuel filter for standard 5mm fuel line.
Super awesome 5mm Tygon fuel line for all your fuel flowing needs.
Blue light up spark plug cap for checking your spark and having an awesome glow down by your engine.
Change your plug on the go with this 3/16" spark plug tool.
Minarelli v1 clutch retaining clip used to keep starting plates locked in.
Used forward facing stock intake for Minarelli v1 engines.
Used v1 internal main drive gear. Angled gears for use with angled gear clutch bells. Be sure to get a crown nut for this if you need it.
Minarelli v1 pedal shaft, just in case you bent, broke or lost yours!
Used original exhaust bracket for General or Lazer exhausts. The end with the big hole mounts onto the swingarm bolt, the other mounts to the pipe.
Used fork triple-tree top plate for General or Lazer mopeds. This one has a shitty powder coat job.
16 x 25 x 5 engine seal for Derbi, Tomos and Morini
15 x 25 x 5 engine seal for Vespa, Minarelli and Morini
Pietcard auto retarding CDI box #2041. Works with all the Puch e50 pietcards and the Minarelli pietcard. This for sure comes with instructions so don't be scared!
Awesome 2 wire on/off ignition switch perfect for mopeds.
NGK spark plugs. BHS series. Best in the world!
NGK spark plugs. Resistor type short thread plugs.
NGK spark plug boot LB05EP. This is the resistor type that uses the little cap on the tip of the plug. 90 degree bend for those hard to reach places!
Small fuel filter for all mopeds. Perfect for tight spaces like moby or maxi!
Clear light up spark plug cap for checking your spark and having an awesome glow down by your engine.
20mm square port intake for Dellorto PHBG clamp or spigot carbs.
Performance replacement for any crankshaft needing a 12 x 15 x 15 needle bearing - Puch, Tomos, Minarelli, Morini, Derbi, Peugeot.
Awesome quality 15mm dellorto SHA square port intake. Use this on most puch stock cylinders, e50 and za50 and all puch 70cc piston port cylinders. This also fits on v1 cylinders perfecto.
Original minarelli v1 flywheel nut. This will work on all model v1 engines and carabela too!
Minarelli v1 regular [right hand] threaded clutch nut. Check to make sure you don't need the reverse thread clutch nut!
Used stock pan style exhaust pipe for Minarelli v1 or Carabela engines.
Used but original Minarelli v1 grey plastic air filter cover. 60mm ID
New old stock piston for minarelli v1 engines. Measures 38.8mm. Made by Asso-werke. Comes withe piston, two 38mm x 1.5mm FG piston rings, wrist pin and clips.
New old stock crankshaft for Minarelli v1 or Carabela. It's actually Carabela branded, but is the same as a normal v1. This is a brass bushing crank that uses a stub plane clutch.
New old stock crankshaft for Minarelli v1 or Carabela. This is a roller bearing crank that uses a tapered clutch. The small end on the con-rod uses a needle bearing instead of a brass bushing, so it's the perfect choice if you're going to be running one of the v1 polini kits.
Awesome upgrade Dellorto SHA carb for most bikes.
Trail Tech A/C Voltage Regulator. Stop blowing out those lights on kitted bikes! -Improved A/C Regulator with Adjustable Output.