Used puch e50 engine cases in the nude already BORED OUT TO ACCEPT PUCH GILA CYLNDERS!!!!! The new over-bore size is 51.5mm.
Universal Piston ring measuring 45mm x 1.5mm with a GI enclosure. Used on many many kits including the puch 45mm Airsal kit. Check yours to see if ya need this one.
CDI stator plate for Puch e50 and za50, Sachs 505 and Derbi. You may have to flip the pick-up coil on the stator depending on what engine you're putting this on - no biggie! This is the stator only - no flywheel. We've had success using the blue GY6 CDI box, [wiring instructions to come!] but you should get crazy and experiment with different boxes, then report back!
Stage6 Vforce3 8 petal reed block for Puch 74cc 47mm Gilardoni cylinders. Perhaps one the best performance upgrades you can make on your Gila kit. The amount of untapped power this releases is unparrelled.
Puch e50 crankshaft + crank bearings and seals rebuild kit. Saves you a few bucks from buying them all separate! Click for kit details...
46mm Airsal cylinder head for Puch e50 and za50. Super big fin for ultimate cooling power. Grab the matching 46mm 72cc cylinder kit!Airsal 04031446
Gigantor 46mm 72cc Airsal cylinder kit for Puch e50 and za50. Super big fin for ultimate cooling power. This is the largest kit you can fit onto a Puch engine without boring the case! Massive intake and exhaust ports with 4 auxiliary boost ports.
Puch maxi length chrome forks. These are a great upgrade from the stock forks and a cheaper alternative to EBR's.
Transmission fluid oil fill level bolt for puch e50 engines. This is the one that threads into the side of the e-50 clutch cover.
Clear light up spark plug cap for checking your spark and having an awesome glow down by your engine.
45mm 70cc airsal kit for puch e-50 and za50.
38mm 50cc airsal kit for puch e-50 and za50.
Replacement 70cc 45mm Airsal piston for the av7 and av88 motobecane 45mm 70cc Airsal kits just in case you blew yours up.
Replacement 70cc 45mm airsal piston for the puch 45mm airsal kits just in case you blew yours up. Or you can get just the 45mm piston ring for this.
NGK spark plugs. BHS series. Best in the world!
Super awesome 5mm Tygon fuel line for all your fuel flowing needs.
Folding Pegs for you and a buddy. These mount over the rear shock bolt.
NGK spark plug boot LB05EP. This is the resistor type that uses the little cap on the tip of the plug. 90 degree bend for those hard to reach places!
Gooooold KMC 1/8" pedal chain for starting your moped. Comes with 112 links and a master link.
Silver KMC 1/8" pedal chain for starting your moped. Comes with 112 links and a master link.
Red light up spark plug cap for checking your spark and having an awesome glow down by your engine.
Used Puch exhaust pipe heat guard. Bolt this right up to your stock maxi pipe or make it fit on anything else!
Transmission fluid drain bolt for puch e50 engines. Get the gasket too if you need it.m8 x 1.25mm threading
PSR P8 exhaust for all angle port Puch cylinders.
Replacement bearing and cup set for puch maxi headsets, will also work on newport, nostalgia, swinger and pinto.
Awesome upgrade Dellorto SHA carb for most bikes.
Night and day upgrade from your crappy stock forks especially for kitted folks.
Puch maxi length chrome EBR forks. Night and day upgrade from your crappy stock forks especially for kitted folks.
Night and day upgrade from your crappy stock forks especially for kitted folks. Blk blk blk.
All four cables you need to completely re-cable your one speed puch e50. For maxi, magnum, pinto, freespirit, swinger, cobra anything with an e50!
HK kevlar racing clutch for Puch E50 moped engines
Spring loaded EBR front forks for Tomos and Puch Maxi - disc brake only!
High flowing performance enhancing speed crushing metal mesh air filter for bing carbs. Fits your 12mm, 14mm or 15mm bing carburetor. You may have to bore out the ID a little for an easier fit or just jam it on.
High flowing performance enhancing speed crushing blue foam air filter for bing carbs. Fits your 12mm, 14mm or 15mm bing carburetor. You may have to bore out the ID a little for an easier fit or just jam it on.
High flowing performance enhancing speed crushing red foam air filter for bing carbs. Fits your 12mm, 14mm or 15mm bing carburetor. You may have to bore out the ID a little for an easier fit or just jam it on.
Aftermarket stock Puch airbox filter for your 12mm, 14mm or 15mm bing carburetor.
Black domino style rear brake lever assembly with bonus grip already installed. Super low profile assembly for a nice clean look on your bars. Spring loaded plastic brake lever, brake lever is about 5.7" long. Use these on any moped - 7/8 or 22mm handlebars.
Replacement black handlebar clamp for maxi and magnum EBR forks.
New new new very nice set of black sidecovers for puch maxi.
Black puch cable guide for all your maxi cable guiding needs.
Replacement stock dual ring piston for puch maxi, newport magnum etc.
New puch long seat for you and a friend. Mount this up to your puch maxi or newport easy-peezy.
Super nice quality superman shape tail light for letting the folks behind ya know you're there.
Super nice quality supermanish shape tail light for letting the folks behind ya know you're there.
Stock tomos metal lined exhaust gasket for a3, a35 and a55. -22mm ID-43mm stud hole spacing from center to center
TOP brand puch two speed za50 unstuffed crankshaft. Check out our words from the wizards within...
Fork brace for keeping your fork legs together. You need this if you've upgraded to puch ebr forks. These also have a nifty fender bracket so you can keep your front fender!
Rear brake cable for Puch and lots of other mopeds.
Awesome quality puch race crankshaft and needle bearing made by DMP. Un-stuffed crank for super high rpms and wide powerband.