5mm Dellorto main jets in the 50's range: 50, 52, 54, 56, 58. For use in all SHA and PHBG carbs
Replacement filter for your 14.9, 14.12, 14.14,15.15 and 16.16 Dellorto SHA. Includes the screen, cap and clip.
Super nice quality supermanish shape tail light for letting the folks behind ya know you're there.
Black plastic throttle and matching 7/8 grip from Lusito.
Round black headlight with chrome rim for all mopeds. The socket in this head light uses an 1157 dual filament bulb.
Cheap effective universal puller for lots of bikes - e50, v1, m1 & m01, use it to pull an hpi etc.
1mm thick reducing shim for dellorto carburetors. Only works with 15.15 and 16.16 carbs. 21mm OD19mm ID
Authentic Dellorto SHA made in Italy. Awesome upgrade carb for most bikes. Slap this on your motobecane, peugeot, puch, minarelli, garelli, sachs, morini or tomos and forget about it. This is the click choke version.
5mm Dellorto main jets in the 70's range: 70, 72, 74, 76, 78. For use in all SHA and PHBG carbs.
5mm Dellorto main jets in the 80's range: 80, 82, 84, 86, 88. For use in all SHA and PHBG carbs.
Stock tail light. This came standard on lots of bikes including puch and tomos. Fit this on pretty much any moped ever!This uses 2x single filament bulbs.
Super nice quality superman shape tail light for letting the folks behind ya know you're there.
Catch all the crud with these internal banjo filters for Dellorto SHA carbs. Fits 14-16mm carbs.
Super heavy duty universal ignition condenser for wiring externally. Get some new connectors if you need them.
Red light up spark plug cap for checking your spark and having an awesome glow down by your engine.
Folding Pegs for you and a buddy. These mount over the rear shock bolt.
Blue light up spark plug cap for checking your spark and having an awesome glow down by your engine.
Change your plug on the go with this 3/16" spark plug tool.
Minarelli v1 clutch retaining clip used to keep starting plates locked in.
Used forward facing stock intake for Minarelli v1 engines.
Used v1 internal main drive gear. Angled gears for use with angled gear clutch bells. Be sure to get a crown nut for this if you need it.
Minarelli v1 pedal shaft, just in case you bent, broke or lost yours!
Awesome 2 wire on/off ignition switch perfect for mopeds.
ADD TO CART TO CHECK STOCK!NGK spark plugs. BHS series. Best in the world!
ADD TO CART TO CHECK STOCK!
NGK spark plugs. Resistor type short thread plugs.
NGK spark plug boot LB05FP. This is the resistor type that uses the little cap on the tip of the plug. 90 degree bend for those hard to reach places!
Clear light up spark plug cap for checking your spark and having an awesome glow down by your engine.
20mm square port intake for Dellorto PHBG clamp or spigot carbs.
Performance replacement for any crankshaft needing a 12 x 15 x 15 needle bearing - Puch, Tomos, Minarelli, Morini, Derbi, Peugeot.
Original minarelli v1 flywheel nut. This will work on all model v1 engines and carabela too!
Minarelli v1 regular [right hand] threaded clutch nut. Check to make sure you don't need the reverse thread clutch nut!
Used stock pan style exhaust pipe for Minarelli v1 or Carabela engines.
stock black dellorto SHA carburetor forward facing air filter for any
bike using an sha prettty much. this one is branded motori minarelli for
all your brand enthusiasts out there.
and many others of course..for larger dellorto SHA carburetors 14.12, 15.15, 16.16
includes the plastic air box + clamp but no mesh filter!made by malossi.04 0843
New old stock piston for minarelli v1 engines. Measures 38.8mm. Comes withe piston, two 38mm x 1.5mm FG piston rings, wrist pin and clips.
New old stock crankshaft for Minarelli v1 or Carabela. It's actually Carabela branded, but is the same as a normal v1. This is a brass bushing crank that uses a stub plane clutch.
New old stock crankshaft for Minarelli v1 or Carabela. This is a roller bearing crank that uses a tapered clutch. The small end on the con-rod uses a needle bearing instead of a brass bushing, so it's the perfect choice if you're going to be running one of the v1 polini kits.
Awesome upgrade Dellorto SHA carb for most bikes.
Trail Tech A/C Voltage Regulator. Stop blowing out those lights on kitted bikes! -Improved A/C Regulator with Adjustable Output.
Dual filament double contact BAY15D bayonet base bulb for moped tail lights. 13.5 Volt .69 Amp 9.32 Watt.
You need this insert for superman tail light assemblies. This is the two bulb style, one for a 5w bulb and one for a 10w bulb.
Universal 12mm sealed axle bearing for front wheels. 165m with spacers.
Universal high tension/external ignition coil for any moped you can fit it on. Works great with 6v or 12v points or CDI!
Check the pics for examples of what's included. Each pack is approximately 20 random pieces. Super grab-bag style!
+2k RMP red clutch springs orginally for GY6 but these should fit honda hobbit, derbi piston port and pyramid reed, minarelli v1, etc. These springs are super universal and should fit on most bikes using this style ~30mm clutch springs.
Blue 280mm - 300mm length rear shocks for puch maxi, tomos, minarelli, morini etc.
Red 280mm - 300mm length rear shocks for puch maxi, tomos, minarelli, morini etc.
280mm - 300mm length rear shocks for puch maxi, tomos, minarelli, morini etc.
5mm Dellorto main jets in the 60's range: 60, 62, 64, 66, 68. For use in all SHA and PHBG carbs