+25lbs of resistance from the stock spring for 1st and 2nd puch za50 and tomos clutches, saxonette clutches and m101 rear variators.
+30lbs of resistance from the stock spring for 1st and 2nd puch za50 and tomos clutches, saxonette clutches and m101 rear variators.
5mm Dellorto main jets in the 50's range: 50, 52, 54, 56, 58. For use in all SHA and PHBG carbs
Replacement filter for your 14.9, 14.12, 14.14,15.15 and 16.16 Dellorto SHA. Includes the screen, cap and clip.
Super nice quality supermanish shape tail light for letting the folks behind ya know you're there.
Black plastic throttle and matching 7/8 grip from Lusito.
Round black headlight with chrome rim for all mopeds. The socket in this head light uses an 1157 dual filament bulb.
Cheap effective universal puller for lots of bikes - e50, v1, m1 & m01, use it to pull an hpi etc.
1mm thick reducing shim for dellorto carburetors. Only works with 15.15 and 16.16 carbs. 21mm OD19mm ID
Authentic Dellorto SHA made in Italy. Awesome upgrade carb for most bikes. Slap this on your motobecane, peugeot, puch, minarelli, garelli, sachs, morini or tomos and forget about it. This is the click choke version.
Black domino style throttle with bonus grip already installed. This is just like the throttles that came stock on lots of Italian mopeds. Super low profile throttle assembly for a nice clean look on your bars.
5mm Dellorto main jets in the 70's range: 70, 72, 74, 76, 78. For use in all SHA and PHBG carbs.
5mm Dellorto main jets in the 80's range: 80, 82, 84, 86, 88. For use in all SHA and PHBG carbs.
Replacement petcock fuel valve for Honda Hobbit, Camino, PA50, and PA50ii. Also works on lots of Italian bikes - Garelli, Minarelli, Morini, Vespa - any bike needing a 12mm x 1mm petcock thread.
Stock tail light. This came standard on lots of bikes including puch and tomos. Fit this on pretty much any moped ever!This uses 2x single filament bulbs.
Complete used clutch assembly for replacing the clutch on your Morini m1 or m01.
Used CEV 6940 flywheel for any Morini using a CEV stator plate. Comes with the flywheel nut.
Super nice quality superman shape tail light for letting the folks behind ya know you're there.
Catch all the crud with these internal banjo filters for Dellorto SHA carbs. Fits 14-16mm carbs.
Super heavy duty universal ignition condenser for wiring externally. Get some new connectors if you need them.
Red light up spark plug cap for checking your spark and having an awesome glow down by your engine.
Folding Pegs for you and a buddy. These mount over the rear shock bolt.
Clear fuel filter for standard 5mm fuel line.
Super awesome 5mm Tygon fuel line for all your fuel flowing needs.
Blue light up spark plug cap for checking your spark and having an awesome glow down by your engine.
New old stock aluminum cylinder for Morini case inducted M1 engines. There's some light surface rust on the bore, but nothing some DW and light sand paper can't handle. Bore size is 40.4mm.
Change your plug on the go with this 3/16" spark plug tool.
Lightly used intake manifold for the 2-speed Morini m02 cylinders.
16 x 25 x 5 engine seal for Derbi, Tomos and Morini
15 x 25 x 5 engine seal for Vespa, Minarelli and Morini
Awesome 2 wire on/off ignition switch perfect for mopeds.
All aluminum head gasket for stock morini motors - m1, m01, m02, m101.
NGK spark plugs. Long thread BES series.
NGK spark plugs. Resistor type long thread plugs.
NGK spark plug boot LB05FP. This is the resistor type that uses the little cap on the tip of the plug. 90 degree bend for those hard to reach places!
Small fuel filter for all mopeds. Perfect for tight spaces like moby or maxi!
Clear light up spark plug cap for checking your spark and having an awesome glow down by your engine.
Performance replacement for any crankshaft needing a 12 x 15 x 15 needle bearing - Puch, Tomos, Minarelli, Morini, Derbi, Peugeot.
Allen bolt set for Morini M01 flywheel and clutch covers.
Used but original Minarelli v1 grey plastic air filter cover. 60mm ID
Awesome upgrade Dellorto SHA carb for most bikes.
Trail Tech A/C Voltage Regulator. Stop blowing out those lights on kitted bikes! -Improved A/C Regulator with Adjustable Output.
Used sidecovers for a Motomarina Sebring or a Motomarina Raven annnnnnd Sachs G3 maybe?
Dual filament double contact BAY15D bayonet base bulb for moped tail lights. 13.5 Volt .69 Amp 9.32 Watt.
Crankshaft seal for Puch ZA50, Tomos A3, A35, A55, Minarelli v1, Morini M1 and M01.
You need this insert for superman tail light assemblies. This is the two bulb style, one for a 5w bulb and one for a 10w bulb.
Used 9mm intake for a reed valve Morini M1 motor.
Universal 12mm sealed axle bearing for front wheels. 165m with spacers.
Universal high tension/external ignition coil for any moped you can fit it on. Works great with 6v or 12v points or CDI!
Check the pics for examples of what's included. Each pack is approximately 20 random pieces. Super grab-bag style!